Solutions to plastic wiring and drawing during 3D printing

BySteve Lowry 2018-09-03 1302

When there's some small plastic remains on the printouts, the drawing exists, this is because the plastic comes out of the nozzle when the nozzle moves to a new position. Fortunately, there are couples of settings in Cura can help solve this problem.

plastic wiring and drawing in 3D printing

 

The most common way to solve the drawing problem is to "retraction". If retraction is on, then when the extruder finishes printing an area of the model, the wire in the nozzle will be pulled back so that when the print is reprinted, the plastic will be pushed back into the nozzle and squeezed out of the top of the nozzle. To confirm that retraction is already start, click on "Advanced - Filament".

 

Retraction speed

The most important setting for withdrawal is the withdrawal distance. It determines how much plastic it will pull back from the nozzle. In general, the more plastic that is pulled back from the nozzle, the less likely it is that the nozzle will move when the nozzle moves.

 

plastic wiring and drawing in 3D printing

 

The normal withdrawal length is set in the interval of 6-10mm. It also depends on the characteristics of consumables.

Retraction speed

 

The relevant setting for the next withdrawal is the retraction speed. It determines how fast the filament is pulled from the nozzle.

 

plastic wiring and drawing in 3D printing

 

If the retraction  is too slow, the plastic will hang from the nozzle, and then begin to leak before moving to a new location. If the  retraction is too fast, the wire may be disconnected from the plastic in the nozzle, and even the driving gear may rotate quickly, and the surface portion of the wire may be cut off. The range of the better retraction is  between 3600-6000mm/min (60-100mm/s). the exact vale depends on the filament you used. So you need to do some tests to make sure the different speed, and whether reduce the amount of drawing.

 

Gearbest Alfawise U20 3D printer mini banner

The temperature is too high

 

If you have checked the retraction settings, the next common problem is that the filament drawing because of the extruder’s temperature

 

plastic wiring and drawing in 3D printing

 

If the temperature is too high, the plastic in the nozzle will become very viscous and will flow out of the nozzle more easily. Then, if the temperature is too low, the plastic will remain hard and difficult to squeeze out of the nozzle. If you think that your retraction settings is correct, but this problem still occurs, try reducing the extruder temperature by 5 to 10 degrees. This will have a significant effect on the final print quality. The normal PLA printing temperature is between 190 - 210 degree.

 

If the temperature is set too high, the rate of the melted material will cause the retraction to be not clean enough, and it will be easy to draw. Therefore, the proper nozzle print temperature setting is a direct effect on the printing model.

Floating distance is too long

 

As we discussed above, wire drawing takes place in the extruder and moves between two different positions. Plastic moves from the nozzle during the movement. The length of the moving distance has a great influence on the generation of drawing. The short-range move is fast enough that the plastic does not have time to re-fall from the nozzle. Then, large distance movements are more likely to lead to drawing. This is no way to change in Cura.

 

plastic wiring and drawing in 3D printing

 

 

Note: Fortunately, Simplify 3D includes a very useful feature to make the moving path as small as possible. The software is very smart and can automatically adjust the path of movement to ensure that the distance the nozzle is vacant is very small.

 

 

 You may also want to read:
 Pick the right 3D printer filament
 How to stop 3D prints from warping
 Cura 3D slicing software installation and operation
 Build new worlds: all you need to know about 3D printing

 

Gearbest Anet A8 Desktop 3D Printer

You might also like

HOT TOPICS

Related Products