Home > Flight Controller > Flight Controller

DetailsDescriptionReviews

Flash Sale

$18.99 20%OFF
15pcs left
Ends in

Email Only

$18.99
Ends in

FuriBee F3 32-bit Brushed Flight Controller

1S 4.2V Input with FrSky 8CH Receiver for Mini RC Racing Drones

4.9 22 Reviews
Additional Purchase Deal: For any Item Total over 60.00, purchase 1 Special Promo Item for 3.99, Discounts are automatically applied to your shopping cart before checkout. View Promo >>
Warehouse Ships on Oct 23
China
Buy Together & Savediscount:17.97

CUSTOMER REVIEWS

  • CouchFlyerRC

    Sep/21/2017 12:51:25
    Pros:
    The Furibee F3 with Flysky receiver is relatively simple to install. It comes with a bag of mounting screws, foam washers and a 1S battery connector. This board to frame design uses 4 screws and foam washers for a “soft mount”. A steady hand is needed to solder the battery connector and the VTX/camera on to the board. The motors have 2 pin micro connectors and plugged right in. The USB connection stands clear of the FPV camera mount at the rear for accessibility. The receiver is 8 ch PPM and uses the AFHDS protocol. Following standard procedure, a binding button is located at the front of the board. Aux switches were then enabled on the transmitter with corresponding channels for arming and modes in Cleanflight. I guess the receiver sensitivity is okay for short distance but solder pads are available for a separate receiver. Success with configuring the FCB is relative to the experience of the user. The SP Racing flight control was flashed with a version of Cleanflight Configurator which requires updating the firmware before it can be used. Many changes to the configuration are necessary after the update but the default Cleanflight PID settings work very well. In this case, the board is used in combination with a 220 mAh 35C LiPo battery and 18000KV motors. Flights last 7 minutes.
    Cons:
    When connected to Cleanflight, USB interferes with the battery voltage. Also, If the transmitter is on the changes to the configuration appear to be saved but aren’t. The Low voltage cutoff is kind of late (6.7V). There is a very infrequent drop out and I can't identify the cause of it.
  • Davide

    Sep/18/2017 21:11:27
    Pros:
    Best FC for tiny whoop. Easy to config for BF and CF.
    Cons:
    High price but good quality
  • Aneel

    Aug/01/2017 18:05:48
    Pros:
    Easy to bind. Power terminals are a bit weird. 5V output solder points the very tiny. Fits perfectly on FuriBee or Eachine frame.
    Cons:
    Yaws a bit when I give it a punch out. Could possibly be my motors as well. Loses telemetry at close range to transmitter.No beeper terminals.
view more

Newsletter

Currency

Copyright ©2014-2017 GearBest.com All Rights Reserved.


Main Features:
- Based on F3 flight controller, FuriBee F3 flight controller features some improvements
- Its high-performance STM32F303CCT6 32-bit processor with 256KB flash brings you better flight experience
- The FrSky receiver is characterized by 200m long receive distance, data return, and stable signals
- Caters different groups by supporting 1S 4.2V input, onboard 5V and 3.3V output
- It can be connected to video transmitters and other receivers
- Excellent electric circuits. There is always 1A output current at 5V, which ensures the high performance of both the flight controller and its peripherals
- Supports signal input of SBUS, DSM satellite, PPM receivers, offering you more options
- Micro USB connector for programming
- Suitable for mini RC quadcopters like Blade Inductrix, E010, JJRC H36, FuriBee F36 and so on

Specifications:
- STM32F303CCT6 32-bit processor with 256KB flash
- MPU6050 gyro / accelerometer
- High quality, gold plated PCB
- Integrated FrSky 8CH receiver, serial port output
- With the built-in DC-DC boost circuit, it can be powered by other devices via IIC or UART port
- Motor drive frequency: 2K ( it can be set by users, 32K at maximum )
- Parameters can be configured in CleanFlight
- Dimension: 27.5 x 27.5mm
- Weight: 2.7g

Note:
The protective frame and the motors in the picture are not included.

Specification

General

Brand: FuriBee
Type: Flight Controller

Flight Controller

Flight Controller Type: F3

Dimension and Weight

Package weight: 0.0200 kg
Product size (L x W x H): 2.75 x 2.75 x 0.10 cm / 1.08 x 1.08 x 0.04 inches
Package size (L x W x H): 4.00 x 4.00 x 1.00 cm / 1.57 x 1.57 x 0.39 inches

Package Contents

Package Contents: 1 x F3 Flight Controller, 1 x Power Cable, 4 x Shock Absorber, 4 x Screw
FuriBee F3 32-bit Brushed Flight Controller Integrated with FrSky 8CH Receiver
FuriBee F3 32-bit Brushed Flight Controller Integrated with FrSky 8CH Receiver
FuriBee F3 32-bit Brushed Flight Controller Integrated with FrSky 8CH Receiver
FuriBee F3 32-bit Brushed Flight Controller Integrated with FrSky 8CH Receiver
FuriBee F3 32-bit Brushed Flight Controller Integrated with FrSky 8CH Receiver

Product Safety Disclaimer:
We do not accept any responsibility or liability for misuse of this or any other product. All our products are extensively tested to comply with rigorous and strict QC standards. For certain products (e.g. toys, knives, etc.), we recommend proper supervision as we cannot be held liable for misuse or accidents.

Small Parts Disclaimer:
These toys contain small parts, not for children under 3 years in case of swallowing or choking . We do not accept any responsibility or liability for misuse of this or any other product.
4.9
Price
Ease of Use
Build Quality
Usefulness
Overall Rating
  • CouchFlyerRC

    Sep/21/2017 12:51:25
    Pros:
    The Furibee F3 with Flysky receiver is relatively simple to install. It comes with a bag of mounting screws, foam washers and a 1S battery connector. This board to frame design uses 4 screws and foam washers for a “soft mount”. A steady hand is needed to solder the battery connector and the VTX/camera on to the board. The motors have 2 pin micro connectors and plugged right in. The USB connection stands clear of the FPV camera mount at the rear for accessibility. The receiver is 8 ch PPM and uses the AFHDS protocol. Following standard procedure, a binding button is located at the front of the board. Aux switches were then enabled on the transmitter with corresponding channels for arming and modes in Cleanflight. I guess the receiver sensitivity is okay for short distance but solder pads are available for a separate receiver. Success with configuring the FCB is relative to the experience of the user. The SP Racing flight control was flashed with a version of Cleanflight Configurator which requires updating the firmware before it can be used. Many changes to the configuration are necessary after the update but the default Cleanflight PID settings work very well. In this case, the board is used in combination with a 220 mAh 35C LiPo battery and 18000KV motors. Flights last 7 minutes.
    Cons:
    When connected to Cleanflight, USB interferes with the battery voltage. Also, If the transmitter is on the changes to the configuration appear to be saved but aren’t. The Low voltage cutoff is kind of late (6.7V). There is a very infrequent drop out and I can't identify the cause of it.
  • Davide

    Sep/18/2017 21:11:27
    Pros:
    Best FC for tiny whoop. Easy to config for BF and CF.
    Cons:
    High price but good quality
  • Aneel

    Aug/01/2017 18:05:48
    Pros:
    Easy to bind. Power terminals are a bit weird. 5V output solder points the very tiny. Fits perfectly on FuriBee or Eachine frame.
    Cons:
    Yaws a bit when I give it a punch out. Could possibly be my motors as well. Loses telemetry at close range to transmitter.No beeper terminals.
  • John Brandenburg

    Jul/25/2017 12:13:59
    Pros:
    Great product from Gearbest, its simple to install, just plug and play. Fast shipping to the Netherlands.
    Cons:
    None
  • Crunchy

    Jul/25/2017 10:55:51
    Pros:
    New design. Easy to use binding button. Tunable Up to date cleanflight and now betaflight?! Great range! Handles 615 716 and 720mm motors that I've tried. Handles the fastest gold motors without oscillations. Clean smooth precise power great upgrade
    Cons:
    No beeper
  • Jotaro

    Jul/05/2017 04:05:58
    Pros:
    light and well build, easy to use
    Cons:
    not so cheap
  • Ashley Buchheit

    Jun/14/2017 08:05:29
    Pros:
    Works great...programming is easy also.
    Cons:
    Small spot to solder camera to.
  • Черненко

    Jun/05/2017 01:49:31
    Pros:
    - Nice FC with stable fly - Light
    Cons:
    - Have an issue with DSM2 reciver - Die after 20 fly
  • Abdul Jabbar

    May/24/2017 06:12:02
    Pros:
    Awesome product awesome quality awesome price
    Cons:
    Nil
  • Corrado Zasso

    May/09/2017 04:27:54
    Pros:
    Very nice flight controller, perfect for the furibeeF36. With this FC You can have more pitch, and, even with standard motors, You can turn the F36 in a fast beast (not for beginners!). Furibee gives You no instructions, but GearBest support team kindly and promptly explained to me the correct binding and armament procedure. Be careful with armament: only left stick full down-full right (Flysky).
    Cons:
    Furibee gives You no instructions, but GearBest support team kindly and promptly explained to me the correct binding and armament procedure. The green led over the FC is very shiny, but, due the small size, it is pretty difficult to understand the direction of the mini drone with one only central light. This wonderful FC deserves almost two different positions leds.
  • adam cox

    May/04/2017 21:11:13
    Pros:
    able to change yaw and configure own settings
    Cons:
    haven't found any yet
  • Chan Chi Kong Simon

    Apr/26/2017 02:01:15
    Pros:
    - Has Frsky Telemetry - Fits the H36 frame nicely - Very long range, more than you'll ever need for such a small quad
    Cons:
    - despite what the description says, it doesn't support SBus - will lose connection if you fly very close to the transmitter
  • Milán Krajsek

    Apr/20/2017 08:29:16
    Pros:
    Very good product!
    Cons:
    -
  • Paul Green

    Apr/12/2017 11:22:29
    Pros:
    Flight controller combined with the FrSKY receivers and other - Advanced controller on the CPU F3 - Low price - Good reviews
    Cons:
    - By default, flooded with CleanFlight firmware, not BetaFlight
  • Jarek

    Apr/05/2017 05:20:20
    Pros:
    Great FC. Perfect for Tiny Whoop. Telemetry works.
    Cons:
    none.
  • Terry Obermier

    Mar/30/2017 00:11:37
    Pros:
    easy to install and bind
    Cons:
    none
  • Jan

    Mar/18/2017 06:41:28
    Pros:
    works on betaflight, good prise had no problems
    Cons:
    I cant think of any cons. It works great
  • Francesco Piccininni

    Jan/20/2017 05:07:04
    Pros:
    Ottima schedina di controllo per creare tinywhoop economici
    Cons:
    Non riscontrati
  • Ben

    Jan/13/2017 01:01:24
    Pros:
    Comes with screws and pads for easy install/build!
    Cons:
    I've read about a drop out issue at close range but can't confirm till I've built mine
  • altin anggara

    Jan/10/2017 10:15:13
    Pros:
    Nico fc based om sprf3 board with cleanflight firmwer
    Cons:
    Dumper fc mount is ti big
view more
1284 Cart0 Add to Cart
FuriBee F3 32-bit Brushed Flight Controller

FuriBee F3 32-bit Brushed Flight Controller

$18.99

Warehouse Options

  • China
FuriBee F3 32-bit Brushed Flight Controller

FuriBee F3 32-bit Brushed Flight Controller

$18.99

Size

  • INTEGRATED WITH DSM2 RECEIVER
  • INTEGRATED WITH FLYSKY RECEIVER
  • INTEGRATED WITH FRSKY RECEIVER
  • INTEGRATED WITH DSM2 RECEIVER
  • INTEGRATED WITH FLYSKY RECEIVER
  • INTEGRATED WITH FRSKY RECEIVER

Color

  • GREEN
  • GREEN
Quantity 1
CONFIRM
CANCEL
xArrival Notice

Once new stock arrives,we'll email you immediately!

  • *E-mail Address:

  • Validation Code: