Launch our Cool Free App!
Get $3 Off 1st Order.
Top 7 Reason to Choose YA101:
1. Free Update Life Time: Just Put in the USB and Paste the files into Flash disk
2. Has the Screen Capture Function (CR3001 Do not have this Function)
3. Battery Testing
4. Find The Cause Of The Fault Code
5. Support vehicles 1996 &newer (OBDII &CAN)
6. Multi-Language: English, French, Russian, Spanish,German, Italian, Portuguese, Japanese, Chinese
7. YA101 provides full OBDII/EOBD diagnostic functions and meets protocols such as ISO9141-2, ISO14230-4, SAEJ1850, and ISO15765-4
★ Diagnostic Functions
Use this function to select a vehicle and then proceed to the diagnostic Menu.
★ Read codes
Reads DTCs from vehicles computer with Koeo or KOE
★ Erase Codes
Deletes dtcs from vehicle s memory
★ Live Data
Live Data menu lets you view, record and playback real time PIDs data from the electronic control mod
In live data menu, you can insert the selected item to front by holding pressing the "ok" key for 3 seconds.
★ Freeze Frame
Displays a snapshot of operating conditions at the time of a fault.
★ Vehicle Info
Scan tool displays the vehicle's VIN number, Calibration ID (s) and CVN that identify the software version in the vehicles control module (s.)The tool also displays In-Use Performance Tracking of important readiness monitors.
★ Component Test
Tool will display a list of components and their locations on the vehicle.This function will always appear on the Main Menu. This selection will appear on the Diagnostic Menu only when the tooll has a list of component locations for the currently selected vehicle.
★ On-Board Monitoring
Scan tool controls the operation of vehicle components, tests or systems.
★ On Sensor Test
Displays oxygen sensor monitoring test results from the vehicle's memory, the O2 Monitor Test is NOT an ON-DEMAND TEST.
★ I/M Readiness
Displays a snapshot of the state of the vehicle's OBDII Monitors.
To review I/M Readiness status,make sure that the ignition key is switched to ON with the engine off.
Not all monitors are supported by all vehicles.There are two types of l/M Readiness tests.
Since DTCs Cleared -shows status of the monitors since the DTCs werelast cleared.
This Drive Cycle-shows status of monitors since the start of the currentdrive cycle.
YA-101 DTC Look Up
Looks up definitions of DTCs stored in scan tool, and shows the possiblecauses of the DTC. (NOt every DTC with possible causes reason)
◇ Voltage Test
This function is used to monitor the voltage present on pin 16 of the OBDIIData Link Connector.
Changes tool option displays tool information, and performs tool self-tests.
Allows the user to change the language used by the tool. English is default.
Changes measurement units display metric or imperial.
◇ Data Logging
Turn on /off the data log function to record the device data through vehicle.
Used to check the display screen.
◇ Keyboard Test
Verifies that the keys are working correctly.
YA101 supports Car List:
Note: YA101 only Support 12V Cars, Does not support 24V Cars or Trucks
▲ American Car (Need Standard OBD2 Protocols from 2000 to now):
for Chrysler, for Ford, for GM, For Jeep ...
▲ European Car (Need Standard OBD2 Protocols from 2003 to now):
For Alfa romeo, for SAAB, for Acura, for Opel, for Audi for Seat, for Peugeot, for Renault, for Bentley, for Skoda, for Daewoo, for Benz, for Daihatsu, for Land Rover, for BMW, for Vauxhall, for Citroen, for Volvo, for Fiat, for VW, for Ford, for Jaguar...
▲ Japanese/Korean Car (Need Standard OBD2 Protocols from 2006 to now):
for KIA, for Isuzu, for Honda, for Mitsubishi, for Hyundai, for Dacia, for Lexus, for Mazda, for Nissan, for Subaru, for Suzuki, for Toyota...
▲ Chinese Car:
Need Standard OBD2 Protocols from 2009 to now
How to use ?
☆ Locating Data Link Connector
1.Choose a location under driver side dash under steering wheel) and use that description in both places.
2.If unsure about location of dlc, check vehicl manual or reputable service center about location
☆ Connect the tool
1.If the connector is not there a label should be there indicating the where abouts of the connector.
2:If necessary, remove the cover from the DLC
3.Turn the ignition switch to the on position. Do not start the engine
4.Plug the OBD connector into the Data Link Connector.
5.The tool will attempt to identify the vehicle. If successful, the vehicle identifie displayed. if the vehicle cannot be identified, menus will be shown for you to select the vehicle manually.